CLLT1036/1 Truck Crane

This product has been discontinued and removed from our shelves.

Tips
1. All these parameters are measured under the condition that the truck is static on the solid ground and the platform had been regulated to be at level.
2. The rated lifting capacity includes the weight of host lifting hook of 400kg and the auxiliary lifting hook of 100kg.
When the auxiliary boom is fully extended, the actual lifting capacity of the host lifting boom should be 1650kg lower than the rated value.
3. If the host lifting hook is at the end of host boom arm, the actual lifting capacity of auxiliary boom should be 400kg lower than the rated value, and actual lifting capacity of every boom section supported by the boom-end single pulley should be 400kg lower than the rated value and limited within 3000kg.
When the auxiliary lifting hook is on the boom-end single pulley, the actual lifting capacity of each section of the host boom will be 100kg lower than the rated value.
4. Under the condition of not using the fifth supporting leg, the truck crane is forbidden to lift any weight within the 120° sector in front of itself. Only after the fifth supporting leg is mounted can the equipment finish the lifting task 360° all around itself.
5. Please make sure the boom length in the list you refer to is longer than your actual boom length, and arrange the lifting task no heavier than the smallest rate lifting capacity suggested by the list for the sake of safety.
6. At the end of the table are the minimum luffing angles under different boom lengths. It will be risky to lower the boom down below these minimum luffing angles.

Technical Parameters (truck)
Dimensions Length mm 13200
Width mm 2500
Height mm 3550
Wheel base First-Second mm 1450
Second-Third mm 3600
Load capacity Self weight kg 1350
Axle load Fore shaft kg 37000
Aft shaft kg 12400
Kinetic parameters Rated power of engine kW/(r/min) 24600
Rated torque of engine N.m/(r/min) 213(2200)
Traveling parameters Maximum driving speed km/h 1160(1200-1600)
Minimum turning diameter m 75
Minimum ground clearance mm 24
Approach angle ° 280
Departure angle ° 16.5
Braking length(30km/h) m 13.5
Maximum climbing capacity % ≤10
Fuel consumption per 100 km L 40



40
Technical Parameter (crane)
Performance parameters Maximum lifting capacity t 36
Minimum rated Luffing range m 3
The platform tail slewing radius mm 3894
Maximum lifting torque Standard kN.m 1236
Supporting leg interval Longitude m 5.3
Transversal m 6.1
Lifting height Standard m 10.9
Longest (host boom) m 39.88
Longest (host and auxiliary boom) m 53.92
Boom length Standard m 10.95
Longest (host boom) m 39.75
Longest ( host and auxiliary boom) m 39.75+13.5
Operation parameters Luffing time Full luffing s 45
Extension time Full extension s 85
Maximum slewing speed r/min 2.0
Maximum lifting speed of host boom with single rope (to the third level of height) m/min 110
Auxiliary lifting speed of auxiliary boom with single rope (to the second level of height) m/min 110
Lifting Capacity Parameters (unit: kg)
Luffing range(m) All supporting legs are full extended + fifth supporting leg (360° lifting task)
All supporting legs are full extended (120° front lifting task is forbidden)
Host boom (m) Host boom+Auxiliary boom
10.95 18.15 25.35 32.55 39.75 39.75+8.5 39.75+13.5
20° 20°
3.0 36000







3.5 32500







4.0 28500 21500






4.5 25000 20500






5.0 23000 19500 12000





5.5 20500 18200 12000





6.0 18500 17000 11800 9700




6.5 16800 16000 11500 9300




7.0 15500 14500 11000 9000 7000



7.5 14000 13500 10500 8600 6500



8.0 12700 12200 9850 8400 6500



8.5 11500 11000 9300 8000 6500



9.0
10000 9000 7800 6400 3000


10
8200 8500 7300 6000 2900
2000
11
6800 7500 6900 5700 2780 1950 2000
12
5600 6500 6500 5400 2650 1850 1900
14
4000 4500 5300 4600 2400 1700 1740 1200
16
2800 3500 4000 4100 2130 1550 1560 1100
18

2500 3500 3300 1850 1380 1380 1000
20

1800 2400 2600 1560 1220 1200 900
22

1400 1900 2100 1290 1050 1020 800
24


1500 1650 1040 880 860 700
26


1100 1200 770 710 680 600
28


800 1100 510 540 520 510
30



800 300 380 400 440
32




200 250 320 370
34






250 300
36







220
Magnification 8 6 4 3 2 1
Minimum luffing angle 23° 35° 45° 48°
Luffing curve

Sinomach Changlin Company Limited
Changlin Import & Export Co., Ltd.
Add: No.898 West Huang He Road, Changzhou city, Jiangsu Province, China
Zip Code: 213136
Tel: +86-519-86781288
Mobile: +86-18206118633
Fax: +86-519-86781387
E-mail:
sales@changlin.com.cn
Service@changlin.com.cn