CLLT1070/1 Truck Crane

This product has been discontinued and removed from our shelves.

Tips
1. All these parameters are measured under the condition that the truck is static on the solid ground and the platform had been regulated to be at level. The luffing ranges in list are measured under the condition of rated load. When measure the load capacity of the 11.62m long boom, we make sure all the expansion boom sections had been retracted.
2. The rated lifting capacity includes the weight of host lifting hook of 550kg and the auxiliary lifting hook of 100kg.
When the auxiliary boom is fully extended, the actual lifting capacity of the host lifting boom should be 2300kg lower than the rated value.
3. If the host lifting hook is at the end of host boom arm, the actual lifting capacity of auxiliary boom should be 550kg lower than the rated value, and actual lifting capacity of every boom section supported by the boom-end single pulley should be 550kg lower than the rated value and limited within 4000kg.
When the auxiliary lifting hook is on the boom-end single pulley, the actual lifting capacity of each section of the host boom will be 100kg lower than the rated value.
4. Under the condition of not using the fifth supporting leg, the truck crane is forbidden to lift any weight within the 120° sector in front of itself. Only after the fifth supporting leg is mounted can the equipment finish the lifting task 360° all around itself.
5. Please make sure the boom length in the list you refer to is longer than your actual boom length, and arrange the lifting task no heavier than the smallest rate lifting capacity suggested by the list for the sake of safety.
6. At the end of the table are the minimum luffing angles under different boom lengths. It will be risky to lower the boom down below these minimum luffing angles.

Technical Parameters (truck)
Dimensions Length mm 14200
Width mm 2800
Height mm 3650
Wheel base First-Second mm 1450
Second-Third mm 4300
Third-Forth mm 1350
Load capacity Self weight kg 45700
Axle load Fore shaft kg 19700
Aft shaft kg 26000
Kinetic parameters Engine Loaded Rated power kW/(r/min) 132/1800
Rated torque N.m/(r/min) 750/1300
Unloaded Rated power kW/(r/min) 276/2200 (WEICHAI) /283/1900(Commins)
Rated torque N.m/(r/min) 1460/1200 ~1600(WEICHAI)/1835/1200(Commins)
Traveling parameters Maximum driving speed km/h 75
Minimum turning diameter m 24
Minimum ground clearance mm 260
Approach angle ° 16.5
Departure angle ° 13.4
Braking length(30km/h) m 10
Maximum climbing capacity % 33
Fuel consumption per 100 km L 47
Technical Parameter (crane)
Performance parameters Maximum lifting capacity t 70
Minimum rated Luffing range m 3
The platform tail slewing radius mm 4200
Maximum lifting torque Standard kN.m 2354.4
Supporting leg interval Longitude m 6.0
Transversal m 7.8
Lifting height Standard m 11.54
Longest (host boom) m 43.73
Longest (host and auxiliary boom) m 58.89
Boom length Standard m 11.62
Longest (host boom) m 44.1
Longest ( host and auxiliary boom) m 59.1
Operation parameters Luffing time Full luffing s 52
Extension time Full extension s 105
Maximum slewing speed r/min 2.0
Maximum lifting speed of host boom with single rope (to the third level of height) m/min 130
Auxiliary lifting speed of auxiliary boom with single rope (to the third level of height) m/min 130
Lifting Capacity Parameters (unit: kg)
All supporting legs are full extended + fifth supporting leg (360° lifting task)
All supporting legs are full extended (120° front lifting task is forbidden)
Luffing range(m) Host boom Host boom + Auxiliary boom
44.1m+9.2m
Host boom + Auxiliary boom
44.1m+9.2m
Boom length (m) Auxiliary boom installation angle Auxiliary boom installation angle
11.62m 19.74m 27.86m 35.98m 44.1m 5 15 30 5 15 30
3 70000          




3.5 63000          




4 56000 39000        




5 48000 37000 24000      




6 39000 34000 24000
   




7 30000 28700 23000 18000    




8 23500 22500 21000 17000
 




9   18200 18500 15600 10000  




10   14700 15300 14500 9800 4000




12   10200 11000 11600 9000 3200 2400   2400    
14   7100 8200 9300 8000 2900 2200 2000 2300 1500  
15
5800 7100 8100 7700 2700 2100 1900 2150 1450
16   5300 6000 7100 7000 2500 2000 1800 2000 1400  
18     4800 5600 5900 2200 1800 1700 1800 1300 1000
20     3800 4300 4800 2000 1700 1600 1600 1200 1000
22     2850 3300 3800 1800 1500 1400 1400 1100 900
24       2600 3000 1500 1400 1300 1200 1000 900
26       1900 2400 1200 1200 1100 1100 1000 850
28         1900 900 1000 900 800 900 800
30         1400 600 700 700 600 800 750
32               500
700 700
Magnification 12 7 5 4 3 1 1
Minimum luffing angle of host boom     28 30 45 52 54 53 55 55 58
Luffing curve

Sinomach Changlin Company Limited
Changlin Import & Export Co., Ltd.
Add: No.898 West Huang He Road, Changzhou city, Jiangsu Province, China
Zip Code: 213136
Tel: +86-519-86781288
Mobile: +86-18206118633
Fax: +86-519-86781387
E-mail:
sales@changlin.com.cn
Service@changlin.com.cn