CLLT1025/5 Truck Crane

This product has been discontinued and removed from our shelves.

We refer you to the following lists of the technical parameters for a better understand of our CLLT1025/5 truck crane.
1. All these parameters are measured under the condition that the truck is static on the solid ground and the platform had been regulated to be at level. The luffing ranges in list are measured under the condition of rated load. When measure the load capacity of the 10.5m long boom, we make sure all the expansion boom sections had been retracted.
2. The rated lifting capacity includes the weight of host lifting hook of 300kg and the auxiliary lifting hook of 70kg.
When the auxiliary boom is fully extended, the actual lifting capacity of the host lifting boom should be 400kg lower than the rated value.
3. If the host lifting hook is at the end of host boom arm, the actual lifting capacity of auxiliary boom should be 300kg lower than the rated value, and actual lifting capacity of every boom section supported by the boom-end single pulley should be 300kg lower than the rated value and limited within 3000kg.
When the auxiliary lifting hook is on the boom-end single pulley, the actual lifting capacity of each section of the host boom will be 70kg lower than the rated value.
4. Under the condition of not using the fifth supporting leg, the truck crane is forbidden to lift any weight within the 120° sector in front of itself. Only after the fifth supporting leg is mounted can the equipment finish the lifting task 360° all around itself.
5. Please make sure the boom length in the list you refer to is longer than your actual boom length, and arrange the lifting task no heavier than the smallest rate lifting capacity suggested by the list for the sake of safety.
6. At the end of the table are the minimum luffing angles under different boom lengths. It will be risky to lower the boom down below these minimum luffing angles.

Technical Parameters (truck)
Dimensions Length mm 12660
Width mm 2500
Height mm 3430
Wheel base One-Second mm 4225
Second-Third mm 1350
Load capacity Self weight kg 32400
Axle load Fore shaft kg 7640
Aft shaft kg 19060
Kinetic parameters Rated power of engine kW/(r/min) 220/2300
Rated torque of engine N.m/(r/min) 1100/1200~1600
Traveling parameters Maximum driving speed km/h 72
Minimum turning diameter m 20
Minimum ground clearance mm 282
Approach angle ° 18
Departure angle ° 14
Braking length(30km/h) m 10
Maximum climbing capacity % 30
Fuel consumption per 100 km L 48
Technical Parameter (crane)
Performance parameters Maximum lifting capacity t 25
Minimum rated Luffing range m 3
The platform tail slewing radius mm 3690
Maximum lifting torque Standard kN.m 980
Supporting leg interval Longitude m 5.03
Transversal m 6.1
Lifting height Standard m 10.57
Longest (host boom) m 40
Longest (host and auxiliary boom) m 49.2
Boom length Standard m 10.5
Longest (host boom) m 40
Longest ( host and auxiliary boom) m 48.3
Operation parameters Luffing time Full luffing s 50
Extension time Full extension s 90
Maximum slewing speed r/min 2.5
Maximum lifting speed of host boom with single rope (to the third level of height) m/min 125
Auxiliary lifting speed of auxiliary boom with single rope (to the second level of height) m/min 125
Lifting Capacity Parameters (unit: kg)
Luffing range(m) All supporting legs are full extended + fifth supporting leg (360° lifting task)
All supporting legs are full extended (120° front lifting task is forbidden)
Host boom Host boom: 40m+
Auxiliary boom: 8.3m
Boom length (m) Host boom luffing angle (°) Auxiliary boom installation angle
10.5 14.19 17.88 23.41 28.94 34.47 40 1° 30°
3.0 25000





80 3000 1900
3.5 25000 23000




78 2850 1900
4.0 24500 22000 18000



76 2850 1800
4.5 22000 20500 17000 12000


74 2800 1750
5.0 20000 19000 15700 12000 10000

72 2700 1700
5.5 18000 17700 14700 11500 9500

70 2600 1600
6.0 16000 16000 13700 10900 9000

68 2450 1500
6.5 14200 14000 12800 10400 8500 7000
66 2200 1420
7.0 12900 12700 12000 9800 8000 6800
64 2000 1350
8.0 11000 10900 10600 8800 7600 6300 5500 62 1750 1280
9.0
8900 8800 8000 6800 5800 5000 60 1500 1210
10.0
7200 7100 7300 6200 5300 4800 58 1280 1100
11.0
6000 5800 6600 5700 4900 4500 56 1080 960
12.0

4850 5500 5250 4500 4150 54 920 850
13.0

4100 4800 4900 4200 3850 52 760 700
14.0

3450 4100 4500 3950 3580 50 600 550
15.0


3500 3950 3700 3350 45 290 260
16.0


3050 3450 3350 3150


18.0


2280 2500 2750 2750


20.0



2050 2200 2300


22.0



1550 1700 1850


24.0




1400 1450


26.0




1060 1150


28.0





900


30.0





700


Magnification 8 6 5 4 3 1
Minimum luffing angle 25° 35° 36° 45°
Luffing curve

Related products